Birmingham Roof Pros provides professional metal roofing in Birmingham, AL for residential and commercial properties across Jefferson County and the Birmingham district. We install standing seam and we like it, and we will still talk a fair number of Birmingham homeowners out of it. The reason is the same thing that makes this a good roofing city to work in: the number of things sticking up through the plane.
A standing seam panel is a continuous run of metal that has to expand and contract along its length. Every penetration it passes is a fixed point, and every fixed point needs a curb, a cricket or a properly fabricated pan flashing that lets the panel move. On a plain gable with a single vent stack that is straightforward. On a 1920s house with three brick stacks and a dormer it is expensive and it is fussy.
So the honest arithmetic runs like this. Count the penetrations. If the answer is more than about four on a single plane, the fabrication and detailing cost starts to overtake the panel cost, and the same budget spent on a well-detailed architectural shingle roof will keep you drier for longer. We will run that count with you and show our working. Where metal is clearly right, we specify it properly.
Twenty-four gauge Galvalume or steel with a PVDF finish, concealed clips, factory-formed valleys, and a full cricket on the uphill side of any stack. Panels are cut to length on site, not stretched. Exposed-fastener panels have a place on outbuildings and porch roofs, and almost none on a main residential plane. Where a panel has to die into a wall, the base flashing is soldered or seamed rather than lapped and sealed.
Metal against brick is the detail that decides the job. A single piece of metal caulked to a masonry face is not flashing, it is a delay. We use a base flashing that turns up the brick, a separate counterflashing cut into a raked bed joint, and a bond break at the mortar. Anything else moves at a different rate to the brick and opens within a few seasons.
One more caution particular to this metro. Older houses here carry a lot of original galvanized metalwork, and new copper detailing draining onto it will corrode it. If a copper crown cap or copper valley is on the table, we will price the whole assembly in compatible metal instead of mixing them. Penetration count is on the estimate as a number, next to the fabrication hours it drives, so you can see where the money is going.
Our licensed and insured team brings the right materials and equipment to every job — two-piece counterflashing cut into a raked bed joint, a poured chimney crown with an overhang and a drip kerf, a framed cricket above stacks wider than thirty inches, self-adhered flashing membrane turned up the brick face, sheet-metal thimble covers sealed at abandoned flue openings, corbelled brick stacks standing proud of the ridge — and backs the work with a written workmanship warranty. We serve Birmingham and nearby communities including Hoover, Vestavia Hills, Alabaster, Homewood.
What We Handle
Everything our metal roofing in Birmingham covers
One crew, one point of contact, and the full range of metal roofing work in Birmingham, AL. If it is on this list we do it in house rather than handing it to a subcontractor:
- metal roofing birmingham al
- metal roofing
- standing seam roof jefferson county
- metal roof installation birmingham
- exposed fastener metal roof alabama
- metal roof cost birmingham
- galvalume roofing birmingham al
- metal roof chimney flashing
- residential metal roof alabama
- metal reroof birmingham
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Birmingham services.
Materials, equipment and how we do metal roofing
The difference between metal roofing that lasts and metal roofing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with two-piece counterflashing cut into a raked bed joint, a poured chimney crown with an overhang and a drip kerf, a framed cricket above stacks wider than thirty inches, self-adhered flashing membrane turned up the brick face, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Birmingham job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in Jefferson County and the Birmingham district means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do metal roofing outside Birmingham
Birmingham Roof Pros covers Birmingham and the surrounding communities of Jefferson County and the Birmingham district. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Metal Roofing in Hoover, AL — Jefferson and Shelby counties, population 92,606
- Metal Roofing in Vestavia Hills, AL — Jefferson County, population 39,102
- Metal Roofing in Alabaster, AL — Shelby County, population 33,284
- Metal Roofing in Homewood, AL — Jefferson County, population 26,414
- Metal Roofing in Trussville, AL — Jefferson and St. Clair counties, population 26,123
- Metal Roofing in Bessemer, AL — Jefferson County, population 26,019
Start on the Birmingham Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Birmingham Chooses Birmingham Roof Pros
- ✓We settle the chimney before we price the covering, because on a pre-war Birmingham house that is the item that moves the number
- ✓Every dead flue gets three priced options — rebuild and recrown, cap and keep, or remove below the deck — and we say which we would choose
- ✓Nothing comes down until the fuel question is answered in writing, and a live appliance is re-vented by a licensed mechanical contractor first
- ✓Flashing is two pieces of fabricated metal cut into a raked bed joint, never one piece bedded in sealant
The standards behind metal roofing
Quality here is not a matter of opinion — it is written down. The metal roofing work we do in Birmingham follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every metal roofing project in Birmingham gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free metal roofing free estimate in Birmingham, or request a quote and we'll get right back to you.